#Manual onkyo ht r380 how to
#Manual onkyo ht r380 manual

If the subwoofer Level Calibration is way off in either direction it can result in distortion.

On the other hand, if you want your subwoofer louder than the 75dB level and the Level Calibration is greater than 0dB, turn the volume knob on your sub up a little bit. If you like to run your subwoofer louder than the 75dB level and your Level Calibration is less than 0dB, increase the Level Calibration on your receiver a couple dB. Likewise, if it's much over 3.0dB, you have the volume knob on your subwoofer set too low. If it's much below -3.0dB, turn the volume knob down a little on your subwoofer and run Audyssey again. If you get it about right, after you run Audyssey the Level Calibration for your subwoofer will be within a range from about -3.0dB to +3.0dB. You can also play some music and listen to some movies and adjust it by ear until it sounds natural.

#Manual onkyo ht r380 manual

If you don't have a Radio Shack meter and don't want to get one, read the manual that came with your subwoofer and see what they recommend for the volume knob setting. While the tone is playing, measure the sound level from your preferred seating position and adjust the volume knob on your sub until the Radio Shack meter reads 75dB. Then play the internal subwoofer test tone from your Onkyo. On the Speaker Setup/Level Calibration screen on your Onkyo, set the Subwoofer level to about -3.0dB and set the volume knob on your sub about 1/3 the way up. The best way to set it initially is with a Radio Shack sound level meter. There's some leeway on where that volume knob gets set, but you'll have problems if it's too low or too high. Powered subwoofers always have a volume knob on the back. If you're not getting any sound out of your subwoofer, this is the first thing to check. Both connectors are purple, so it's easy to do. This is a mistake that even experienced people make. One of the symptoms of mistakenly using the Surr Back terminals in a 5.1 setup is Audyssey failing when it tests the Surrounds.

The Surr Back L and Surr Back R terminals only get used for 7.1. That's okay, just make sure you connect them to the Surr L and Surr R terminals. In a 7.1 system, you have two additional speakers behind you connected to the surround back speaker terminals.Д«ecause of room constraints or personal taste, many people with 5.1 systems put the surround speakers in the back of the room. The two on the sides are called the surround speakers and they should be connected to the surround speaker terminals. In a 5.1 system, you should have 3 speakers in front and two on the sides. A lot of people new to home theater assume that in a 5.1 setup you have 3 front speakers and 2 behind you, and that when you go to 7.1, you put the two additional speakers on the sides. It's very easy to have 1 or 2 stray copper wires brush up against the adjacent speaker terminal or the chassis which can trip the protection circuits or damage your receiver.Д¬onsider using banana plugs to avoid this problem, especially at the receiver end, or solder the bare ends of the wires to keep them from fraying. Take your time with the speaker wires, especially if you're using bare wire connections. This is one mistake that can cost you your receiver. If you want to use zone 2/3, you have to run stereo analog cables from your sources to your receiver in addition to any HDMI or SPDIF cables. Bitstreams is very short and includes the Toshiba HD-A35 and HD-XA2 with firmware = 2.7, the Samsung BD-P1400 w/firmware update, the Pioneer Elite 95FD, and the Panasonic DMP-BD30. The list of players that can transmit TrueHD, DD+ etc. Your receiver can't look at the PCM and tell what format it was in originally so it can't turn on the indicator on the front panel. They decode the bitstream and send multichannel PCM. However, in order to see the TrueHD or DD+ or DTS-HD indicators light on your receiver, the player has to send the undecoded bitstream. If you have things configured correctly, you'll get all the benefit of TrueHD, DD+ and DTS-HD with your Onkyo receiver, assuming your HD-DVD or Blu-Ray player is capable. Always set HDMI Audio Out=OFF unless you want to use your television's speakers. Symptoms include not being able to receive any signal format other than 2 channel PCM, getting video but no audio from HDMI sources, and your receiver always being muted when you first turn it on. This one is very common and it causes a lot of problems.

#Manual onkyo ht r380 how to

Here's my list of the 10 most common problems people have with their new Onkyo receivers and how to deal with them. I've spent a lot of time over the last couple months in the various Onkyo receiver threads, and there are a number of issues that come up over and over again.

Manual onkyo ht-r380